|
EuroGoldLS -> How-to: HID Plug & Play install & DRL disable (2/25/2008 2:21:06 PM)
|
How-to: HID Plug & Play install
Some steps may vary for models older than 1998.
To install your new HID plug and play kit, you will need the following materials:
- The kit (complete with wiring, ballasts, ballast mounts, and bulbs.)
- Drill and zip-in screws
- Double sided tape (may be included in some kits)
- Pliers
Your kit should look something like this:
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0042.jpg[/image]
First, when installing in high beams, you must disable your DRLs. To do this and keep your automatic function, read the following:
Go to the fuses located under the hood (black box next to air box.) Open it and find the relay labled DRL.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0051.jpg[/image]
On the bottom of the relay you will see 5 prongs with the numbers 30, 85, 86, 87 and 87a. Use your pliers and bend the prong numbered 86 up toward the top of the relay.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0052.jpg[/image]
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0053.jpg[/image]
This will prevent that prong from engaging and will deactivate the DRL's. Replace the realay and put cover back on.
Pull off your grille. Just open the hood and give it a good pull by the handholds below the crossbar. Make srue you disconnect the parking lights from the bumper lense.
Locate your ballast mounts. They will look similar to this depending on the kit:
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0074.jpg[/image]
I chose to mount mine on the radiator scoop. The radiator scoop will pull air from above the license plate mount. This scoop will vary in shape depending on your model. Mounting it here will provide the ballasts with adequate airflow to keep them cool. You may mount them anywhere, its up to you.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0076.jpg[/image]
Next, you will have to remove the headlights. To do this, locate the tabs on the back of the radiator support.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0060.jpg[/image]
Pull out the tabs, you may have to use pliers, as they are sometimes tight.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0061.jpg[/image]
Once you've remove the headlamp from the radiator support, twist the bulb and pull it out.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0063.jpg[/image]
Undo the bulb from the wiring.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0064.jpg[/image]
Connect the female end of the harness to wiring on the vehicle.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0066.jpg[/image]
Insert the bulb in the headlamp assembly. Be careful NOT to touch the bulb. Fingerprints may weaken the ability of the glass to release heat and cause premature failure.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0067.jpg[/image]
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0068.jpg[/image]
Run the male end of the wiring harness through the hole in the divider flap between the radiator and the headlights. Pull it all the way through.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0071.jpg[/image]
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0072.jpg[/image]
Connect the male end of the wiring to the ballast.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0078.jpg[/image]
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0079.jpg[/image]
The wires coming from the ballasts will connect to the wires coming from the bulb.
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0080.jpg[/image]
[image]http://i260.photobucket.com/albums/ii10/BEblazin4life/how%20to/105_0081.jpg[/image]
Use your double sided-tape to secure the ballast to the mount.
You're done!
|
|
|
|
