3rd row bench in 2nd row? HELP!

Chevy Forum Chevy Classifieds Photo Gallery Chevrolet News Search Contact CF Sponsors
Member List Forum FAQ Chevy Timeslips Chevy Recalls TSBs Calendars Register Login

3rd row bench in 2nd row? HELP!

Printable Version

Chevrolet Forum >> Chevy Trucks, Vans & SUV's >> Venture >> 3rd row bench in 2nd row? HELP!

Page: [1]

Message

<< Older Topic Newer Topic >>

3rd row bench in 2nd row? HELP! - 12/12/2007 9:58:57 PM

dgwestfall

Posts: 5
Joined: 12/12/2007
Status: offline

Hey folks, I'm new to mini vans. I have a 99 Montana, same as the Venture. Can I use my third row bench in the 2nd row? I need 8 seats and I just bought a third row bench from Ebay because I was told that I could use the seats in the 2nd row by the dealer I bought the van from. I just tried to move my 3rd row bench to the second row, and it seems that due to the configuration of the floor anchors, there is no way to make it work. Any advice would greatly help!

Post #: 1

RE: 3rd row bench in 2nd row? HELP! - 12/13/2007 11:16:44 AM

MalibuMaxxSS

Posts: 629
Joined: 11/18/2006
Status: offline

The carpoet will need to be cut and the little plastic bracket you will have to buy, the hole is there in the floor, just not cut out, but yes it is possible, feel the floor for where the bracket should be you will feel a hole, cut the carpet and go to a GM store and get the plastic tab....and you should be golden...

The original configuration was for 3 small seats in the middle row not the bench so the tabs are in different locations, the short came with bench in the middle so the holes are there just not cut yet

< Message edited by MalibuMaxxSS -- 12/13/2007 11:17:34 AM >

_____________________________

2006 Malibu Maxx SS, computer Flashed, undercar LED, Cold air intake, 18' Potenzas, Limo tint front to back

1990 YJ Lifted Locked and always muddy, posi loc, 33s TSLs, weber carb. drop tailgate...

(in reply to dgwestfall)

Post #: 2

RE: 3rd row bench in 2nd row? HELP! - 12/13/2007 3:30:52 PM

dgwestfall

Posts: 5
Joined: 12/12/2007
Status: offline

quote:

ORIGINAL: MalibuMaxxSS

The carpoet will need to be cut and the little plastic bracket you will have to buy, the hole is there in the floor, just not cut out, but yes it is possible, feel the floor for where the bracket should be you will feel a hole, cut the carpet and go to a GM store and get the plastic tab....and you should be golden...

The original configuration was for 3 small seats in the middle row not the bench so the tabs are in different locations, the short came with bench in the middle so the holes are there just not cut yet

I looked again, and there are three slots per side of the van. (I made a diagram below). For instance, if I put one side (drives side) of the bench seat (it's a 50/50 bench) in slot F and E, then it's right against the sliding door and there's a gap in the middle from the other seat. Also, Slots E and D are too close together, so that wont work either. For the seats to fit, for instance on the drivers side, I'd have to put the hooks on the right of the drivers side seat (if you were sitting in the van) in slot D, but the hooks on the left side have no slot to fit into as they fall between F and E. Same on the passenger side. I'd have to put the left hooks of the passenger seat in slot C, but the right site falls in between slot A and B...no slot for them to hook into. Does that make sense?
___
_F_]
            (passenger side slots)

___
_E_]
___
_D_]

-----------------------------Center of Van----------------Front---->
___
_C_]
___
_B_]    (driver side slots)

___
_A_]

(in reply to MalibuMaxxSS)

Post #: 3

RE: 3rd row bench in 2nd row? HELP! - 12/13/2007 7:51:09 PM

nokidz

Posts: 3
Joined: 2/26/2007
Status: offline

i am interested in this as well. i have a seven pass 2001 venture and want to turn it into a 8 pass for a trip. my second row seating is a single seat behind the driver and a single seat in the middle. is there another single seat designed for the third seat behind the passenger side? any help greatly appreciated.

(in reply to dgwestfall)

Post #: 4