key fob programming instructions

Chevy Forum Chevy Classifieds Photo Gallery Chevrolet News Search Contact CF Sponsors
Member List Forum FAQ Chevy Timeslips Chevy Recalls TSBs Calendars Register Login

key fob programming instructions

Printable Version

Chevrolet >> General Chevrolet Forums >> General Tech >> key fob programming instructions

Page: [1]

Message

<< Older Topic Newer Topic >>

key fob programming instructions - 7/9/2006 2:49:38 PM

barecub

Posts: 1
Joined: 7/9/2006
Status: offline

Can anyone get me the programming instructions for late model gm/l format key fob. Specifics= 2005 Chevy Uplander. I bought an additional fob. Some of these ya-hoos online will sell me the instructions for $15 or I have to take it to the dealer and have them program it when it's something I could totally do on my own if I had the instructions. Thanks in advance for any guidence on this.

Post #: 1

RE: key fob programming instructions - 8/25/2006 8:52:29 PM

KissMySS

Posts: 15
Joined: 8/25/2006
Status: offline

can tell you how...free....e-mail me

(in reply to barecub)

Post #: 2

RE: key fob programming instructions - 4/6/2007 9:14:51 AM

klswanky

Posts: 2
Joined: 4/5/2007
Status: offline

I would also like the instruction if you please. GM/L 2007 Uplander

(in reply to KissMySS)

Post #: 3

RE: key fob programming instructions - 4/6/2007 11:04:45 AM

tahoe07

Posts: 1139
Joined: 9/22/2006
Status: offline

According to this site  http://www.programyourremote.com/
Uplanders cannot be programed yourself. Not sure i beleive that.   Try this

1.      Close all vehicle doors.
2.      Insert the key into the ignition.
3.      Hold down the power UNLOCK button on the driver's door panel-continue to hold down until instructed to release.
4.      Perform steps 5 through 8 in fairly rapid succession.
5.      Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6.      Turn the ignition switch to the OFF position.
7.      Turn the ignition switch to the ON position.
8.      Turn the ignition switch to the OFF position.
9.      Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

This site doesn't have 07s so see below...

quote:

ORIGINAL: klswanky

I would also like the instruction if you please. GM/L 2007 Uplander

If you have an 07 with DIC this MAY work

Relearn Remote Key

This display allows you to match Remote Keyless

Entry (RKE) transmitters to your vehicle. To

match an RKE transmitter to your vehicle, do the

following:

1. Press the vehicle information button until

PRESS V TO RELEARN REMOTE KEY

displays.

2. Press the set/reset button until REMOTE KEY

LEARNING ACTIVE is displayed.

3. Press and hold the lock and unlock buttons

on the first transmitter at the same time for

approximately 15 seconds.

A chime will sound indicating that the

transmitter is matched.

4. To match additional transmitters at this time,

repeat Step 3.

Each vehicle can have a maximum of eight

transmitters matched to it.

5. To exit the programming mode, you must

cycle the key to LOCK.

< Message edited by tahoe07 -- 4/6/2007 11:26:28 AM >

(in reply to klswanky)

Post #: 4

RE: key fob programming instructions - 4/6/2007 2:51:50 PM

klswanky

Posts: 2
Joined: 4/5/2007
Status: offline

Sorry Tahoe07 niether one worked for me. I do not have the DIC on my '07 I guess because there was never an option for 'relearn remote key' on the display.

(in reply to tahoe07)

Post #: 5

RE: key fob programming instructions - 6/15/2007 5:09:07 PM

starcity

Posts: 1
Joined: 1/18/2007
Status: offline

Has anyone figured out how to program a 2007 Tahoe/Suburban remote / fob??? If so, please provide instructions. I lost my remote and got a new one. Need programming instructions, is it even possible to do without going to the dealer. Thanks!

(in reply to barecub)

Post #: 6